Matt Rustic Terrazzo Tiles 600 X 600mm And 800X800mm And 600x1200mm
Product Descriptions:
Arpege Digitally Printed Wall Tiles / Marble Effect Ceramic Wall
Tiles
Introduction
full body R10 anti slip, mold made glaze porcelain tile ,using
ink-jet transparent glaze technology,have 12 different
patterns,double zero water absorption,the friction coefficient
≥0.5.
| Model | Arpege Tile AJ6D612W |
| Name: | Morandi Arpege Porcelain Tile |
| Material | Porcelain tile |
| Product Dimensions | 24 x 24 inches |
| Thickness | 9.5mm |
| Finish | concave matt surface |
| pattern | 12random patterns |
| colors | Black color |
| Shade Variation | V4-substantial variation (Color Variation within each tile ) |
| Absorption rate | <0.5% |
| Abrasion resistance | 6 - commercial considerable traffic |
| Function | Chemical resistant and Frost resistant, Acid-resistant,
Antibacterial, Heat insulation, Wear-resistant |
| Usage | Use in indoor and outdoor floor and wall |
| Size(mm) | Pcs/ctn | M2/ctn | Kg/ctn | Ctn/pallet |
| 600x600 (24'x24') | 4 | 1.44 | 31 | 36 |
Guidelines: widely used in the living room, toilet, kitchen wall
floor, flagship store, can also be laid outdoors.
Process characteristics: Can keep color for a long time, hard and
wearable, suitable for use in most indoor spaces
except toilets and kitchens.
Glaze: Concave-convex grinding face plus flash glaze, non-slip,
easy to clean.
Design pattern: Multiple patterns combination, can be mixed with
multiple colors.
1, when opening the box, should recognize the product
specifications, dimensions, color number, etc., the same color
number of the product affixed to the same position, do not mix the
products of different color numbers together pasted
(unless consciously required to obtain Special decorative effects
in the figure)
2, before pasting first on the ground test, after using the same
color number and size, you can use the adjacent color
number and size, and different color number, size tile
classification, and then in the bottom of the brick for use Number
to indicate. If the brick surface has a pattern or directional
pattern, the product should be unified according to the direc
tion of the pattern, in order to best decorative effects.
3, at present, the tile pasting mostly uses wet pasting and dry
pasting two methods.
4, when paving the floor brick, it is recommended that the surface
area of cement mortar paving should not be too large,
so as not to find the surface cement mortar more than the initial
coagulation time(about 45 minutes), resulting in the tile
and adhesive layer adhesion is not dense Real, causing quality
problems such as air drums.
5, when leaving seam pasting, polished brick spacing 2mm-5mm is
appropriate. The polished brick and the wall junction
leave a seam of 3mm-5mm.
6, pasting should be carried out after the base is compacted. When
tiling tiles, the tiles and the pasting surface are first
presented at a certain angle(about 15 degrees), and then pushed
gently to the horizontal direction by hand to balance
the bottom of the brick and the pasting surface.This facilitates
the elimination of bubbles; Then tap the brick surface with
a hammer handle, so that the bottom of the brick can eat pulp, so
as not to produce an empty drum phenomenon; Then
knock the brick surface to level with a wooden hammer and measure
it with a horizontal ruler to ensure The tile pasting
level.
7, about 12 hours after the product is pasted, hit the ground with
a wooden hammer in time to check whether there is an
empty drum phenomenon. All brickwork should be done in time to
remove the surface dirt, 24 hours before walking.
8, pasted tiles within 48 hours, it is best not to use large-scale
waxing and other electric equipment, so as not to tile and
adhesive layer later shock and lead to unnecessary empty drum
phenomenon.
